Data Requirements

Proto-Power Pack Spec Requirements

In Order to Qualify for the Proto-Power Pack, your design must meet the following criteria:
-PROTO-POWER PACK SPECIFICATION REQUIREMENTS-
*Proto-Power Pack Specs will be followed regardless of Fab or Dwg Specs.*
****NO ADDITIONAL PROMO CODES ACCEPTED ON THIS OFFER*****

.062" Thick, Standard FR4, 1 - 2 oz Cu., Standard Tin/Lead HASL, 2 Green Masks, 1 White Top Legend

Individual Pieces Only, Routed. No SCORING. No BEVEL. No Controlled Impedance.

No arrays, No multiple parts and part numbers, No Plated slots, No gold.

MAXIMUM MANUFACTURABLE DIMENSIONS: 17x23 Single & Double Sided- 15.5x21.5 Multi-Layer

Maximum board dimensions shall not exceed 90 sq./in. total.

Tolerances: Holes +/-.003", x/y tolerance +/- .005", annular ring min .008", min LPI dam of .008".

Line and space densities no less than 8 mils, Smallest finished Via .014", Largest finished hole .25".

Click Here to Go Back To Proto-Power Pack!

Terms & Conditions

All data must comply with criteria described in "Data Requirements". Any deviation from these requirements may/will result in additional costs and/or delay ship date.

All orders are pending engineering review and acceptance. Incomplete or inaccurate data supplied by customer may delay processing and if problem persists without timely resolution by the customer, delivery date can be impacted.

Data supplied will be "data built ". eFabPCB is not responsible for any incomplete/incorrect data

Quotes are valid for 30 days.

Quote are subject to change if actual design data and specifications are different than information entered into the original quote.

Files must be received along with order no later than 11:30 a.m. CDT in order for parts to ship following day. ex. 5 day turn = 120 manufacturing hours. Order and data must be received by 9:00 a.m. on a ONE DAY TURN.

ALL ORDERS on the Proto-Power Pack are to be payed by credit card only. COD orders only accepted upon approval from e-FABPCB.com with credit references.We accept Visa, MasterCard, and American Express. You will receive a confirmation of acceptance once card approval is received.

All orders payed by credit card or line of credit($350 min to open account).COD orders only accepted upon approval from eFabPCB.com. FAX CREDIT REFERENCES(847.290.9823) to qualify for "open account status". We will confirm upon approval of your credit limit.

FAX CREDIT REFERENCES(847.290.9823) to set up payment terms. Payment terms are net 30 days. Label pages " eFabPCB CREDIT REFERENCES"

Credit holds will prevent order placement.

eFabPCB payment terms for open account are net 30 days, FOB origin.

Shipping Type is by UPS only, unless we are provided with your Shipping account type and number. You can leave the shipping info in the "Special Notes" section of the order.

eFabPCB.com reserves the right to change the shipping method per our discretion to maintain on-time delivery

Shipping is pre-paid and billed.

Order cancellations subject to 100% cancellation charges if order is in process.

eFabPCB reserves the right to ship and invoice customer for 10% overage.

Reschedules inside of four weeks not allowed unless approved by eFabPCB.

The PROTO-POWER PACK Offer requirements are mandatory and cannot be deviated. ANY SPEC GIVEN THAT DOES NOT FALL INTO THE REQUIREMENTS, WILL BE ADJUSTED OR IGNORED.

Updated 8/3/2005

In order to process your order properly, the following information is needed at order entry:

* Data files uploaded must be formatted in Gerber 274X (Imbedded Aperture Files) or Gerber 274D (Separate Aperture File) .

* NC Drill Files (Excellon format)* Drill Chart & Drill Type REQUIRED (Plated and non-plated)

Fabrication Drawings/notes detailing:

* Material Type

* Board Thickness

* Layer count

* Multi-layer construction if applicable

* Dimensions for part and route features

* Array/panelization drawing if applicable

* Surface Finish Type

* Number of Solder Masks /Color/type

* Number of Legends/location/Color

* Special process parameters and requirements

Fab drawings may be supplied in the following format:

* HPGL files

* Adobe PDF

* Autodesk DXF

* Autodesk DWG

Incomplete files or deviations between the Fabrication drawing/data and quotation could jeopardize lead-time. Please indicate emergency contact number for short lead-time orders in your order entry profile.

File Naming Rules

* All files included in ZIP file must be named with 10 characters max, made up of LETTERS AND NUMBERS ONLY, and NO SPACES followed by a period and three letter extension

* The simplest naming procedure would be to name the files by their layer position:

* *TopLegend.gbr;

* TopMask.gbr;

* Topcirc.gbr;

* Botcirc.gbr;

* BotMask.gbr;

* BotLegend.gbr;

* NCdrill.drl

*Please Note: We highly recommend using this format. It greatly increases file accuracy, speeds up quote time and allows for easier manufacturing.

* Please be sure to keep all Zip File names unique, as we receive hundreds of Zip files on a daily basis.

Zip File Content

* Gerber Formats RS274X (Imbedded Apertures) are preferred! Gerber RS274D (Separated Apertures) are accepted but may be subject to a $35.00 charge for additional engineering time. We highly recommend the use of Gerber RS274X, which does not require the separate output of aperture files. Please remember to send a single, comprehensive aperture list for all 274D files, as opposed to sending an individual aperture file for each 274D file.

* All other files containing Fabrication information and specifications should be in PDF, DXF, DWG and HPGL format. Other formats are not acceptable.

* All drill files (NCD files) must be in Excellon format.

* The Fabrication information must include a board outline (dimensionally labeled), Drill pattern, Drill chart, plated and non-plated information and pertinent manufacturing specifications.

* Text files ("ReadMe.txt" files) can be submitted containing manufacturing notes/special process notes, contact information and layer description